新聞中心
滾珠絲杠在安裝時如何操作的?
來源:http://www.zsdress.com/ 日期:2020-07-08 發布人:
1、滾珠絲杠屬于精密傳動裝置,必須進行潤滑。在螺母內使用家皂基潤滑脂1-3號透平油潤滑。山東博特精工股份有限公司網站|滾珠絲杠|直線導軌|主軸 1.滾珠絲杠屬于精密傳動裝置,必須進行潤滑。在螺母內使用家皂基潤滑脂1-3號透平油潤滑。
1. Ball screw belongs to the precision transmission device and must be lubricated. It is recommended to use soap base grease No. 1-3 turbine oil for lubrication in nuts. The official website of Shandong Bote Precision Industry Co., Ltd. ball screw linear guide shaft 1. Ball screw belongs to precision transmission device, which must be lubricated. It is recommended to use soap base grease No. 1-3 turbine oil for lubrication in nuts.
2.滾珠絲杠與滾動軸承一樣,混入灰塵異物將會降低使用壽命。因此,必須采用絲杠保護套加以保護。國內外各種類型的滾珠絲杠副大部分均已安裝有迷宮式密封環,防止贓物進入滾珠絲杠體內。另外,在金屬屑易侵入絲杠的場合使用時,還應考慮在絲杠全長上采用絲杠保護套防護。
2. Like rolling bearing, ball screw mixed with dust and foreign matters will reduce its service life. Therefore, it is necessary to use the lead screw protective sleeve to protect it. Most of the ball screw pairs at home and abroad have been installed with labyrinth seal ring to prevent dirt from entering the ball screw. In addition, when the metal chips are easy to invade the lead screw, the screw protective sleeve should be used in the full length of the lead screw.

3.由于滾珠絲杠螺母的特殊結構,不宜承受徑向負荷,以免造成絲杠彎曲,影響傳動精度和運動的靈活性,降低使用壽命。故安裝時,尤其要注意絲杠的軸心線與螺母座移動軌跡的平行,并使絲杠支撐軸線與螺母座軸線一致。
3. Due to the special structure of the ball screw nut, it is not suitable to bear radial load, so as to avoid the screw bending, affecting the transmission accuracy and movement flexibility, and reducing the service life. Therefore, during installation, special attention should be paid to the parallelism of the axis line of the lead screw and the movement track of the nut seat, and make the central axis of the screw support consistent with the central axis of the nut seat.
4.將絲杠安裝于設備上,注意不能使絲杠與螺母分離,以免滾珠脫出。安裝時不要敲打滾珠絲杠副,尤其注意保護滾珠導管,因其管壁教薄,碰撞變形將使鋼球流動受制約。
4. Install the lead screw on the equipment. Pay attention not to separate the screw from the nut, so as to prevent the ball from falling out. When installing, do not knock the ball screw pair, pay special attention to protect the ball guide tube, because the tube wall is thin, collision deformation will restrict the flow of steel ball.
以上就是導軌絲杠為大家介紹關于滾珠絲杠的相關內容,希望能夠幫助到大家。如需了解更多相關資訊,請繼續關注我們網站http://www.zsdress.com 后續將呈現更多精彩的內容
The above is the guide screw for you about the ball screw related content, I hope to help you. For more information, please stay tuned to our website http://www.zsdress.com More wonderful content will be presented later
- 上一篇:直線導軌的產品特點是什么?
- 下一篇:直線導軌安裝需要注意的幾點!
- 導軌防腐蝕措施有哪些...<>
- 滾珠絲杠的循環方式解...<>
- 導軌絲桿在陶瓷雕銑機...<>
- 導軌運行阻力怎么測量...<>
- 絲杠傳動中的回差現象...<>
相關: