1、 Keep the guide rail and its surrounding environment clean, even if the invisible smile dust enters the guide rail, it will also increase the wear, vibration and noise of the guide rail.

二、導軌在使用安裝時要認真仔細，不允許強力沖壓，不允許用錘直接敲擊導軌，不允許通過滾動體傳遞壓力。

2、 The guide rail should be carefully used and installed. It is not allowed to punch strongly, hit the guide rail directly with hammer, and transfer pressure through rolling element.

三、導軌使用合適、準確的安裝工具盡量使用專用工具，極力避免使用布類和短纖維之類的東西。

3、 Proper and accurate installation tools shall be used for guide rail, special tools shall be used as far as possible, and cloth and staple fiber shall be avoided as much as possible.

四、防止導軌的銹蝕，直接用手拿取上銀導軌時，要充分洗去手上的汗液，并涂以礦物油后再進行操作，在雨季和夏季尤其要注意防銹。因為導軌屬于精密零件.

4、 To prevent the corrosion of the guide rail, when directly taking the upper silver guide rail by hand, it is necessary to fully wash off the sweat on the hand and coat it with high-quality mineral oil before operation. Pay special attention to rust prevention in rainy season and summer. Because the guide is a precision part

因而在使用時要求有相當地慎重態度，即變是使用了高性能的上銀導軌，如果使用不當，也不能達到預期的性能效果，而且容易使導軌損壞。 不過，在某種特殊的操作條件下，導軌可以獲得較長于傳統計算的壽命，特別是在輕負荷的情況下。這些特殊的操作條件就是，當滾動面（軌道及滾動件）被一潤滑油膜有效地分隔及限制污染物所可能導致的表面破壞。事實上，在理想的條件下，所謂**導軌壽命是可能的。

Therefore, it is necessary to be cautious in use, that is to say, the high-performance silver guide rail is used. If it is not used properly, the expected performance effect can not be achieved, and the guide rail is easy to be damaged. However, under some special operating conditions, the guideway can obtain a longer life than the traditional calculation, especially in the case of light load. These special operating conditions are the surface damage that may occur when the rolling surface (track and rolling element) is effectively separated and limited by a lubricating oil film. In fact, under ideal conditions, the so-called * * guideway life is possible.

潤滑保養：脂潤滑有預先在密封型導軌中充填潤滑脂的密封方式，以及在外殼內部充填適量潤滑脂，每隔一段時間進行補充或更換的充填供脂方式。此外，對有多處導軌需要潤滑的機械，還采用管道連接各潤滑處的集中供脂方式。脂潤滑可做到充填一次潤滑脂后長時間不需補充，而且其密封裝置的結構也較簡單，因此使用廣泛。油潤滑相對來說比較簡單。經常潤滑可以大大提高導軌的使用壽命

Lubrication and maintenance: grease lubrication has the sealing mode of filling grease in the sealed guide rail in advance, and filling and supplying grease mode of filling with proper amount of grease inside the shell and replenishing or replacing at intervals. In addition, for the machinery with multiple guide rails to be lubricated, centralized grease supply mode with pipes connected to each lubricating place is also adopted. Grease lubrication can be achieved after filling the grease for a long time without replenishment, and the structure of its sealing device is simple, so it is widely used. Oil lubrication is relatively simple. Regular lubrication can greatly improve the service life of the guide rail