直線導軌一般來說包括安裝前和安裝后的保養。但在實際的應用當中，有些終端用戶可能不怎么懂得正確保養方法，從而導致出現掉鋼球、爆端蓋等現象。下面導軌絲杠廠家就來講講存放直線導軌應注意的事項。

Generally, linear guide rail includes maintenance before and after installation. However, in practical applications, some end users may not know the correct maintenance methods, resulting in steel ball dropping and end cap explosion. The guide rail lead screw manufacturer will talk about the precautions for storing the linear guide rail.

一、保持導軌及其周圍環境的清潔，保持無粉塵或者固體顆粒物的存在，如以上環境不可避免，請立即更換存放位置。

1、 Keep the guide rail and its surrounding environment clean and free of dust or solid particles. If the above environment is unavoidable, please change the storage location immediately.

二、導軌在使用安裝時要認真仔細，不允許強力沖壓，不允許用錘直接敲擊導軌，不允許通過滾動體傳遞壓力。

2、 The guide rail shall be carefully used and installed. It is not allowed to punch hard, hit the guide rail directly with a hammer, and transfer pressure through the rolling body.

三、導軌使用合適、準確的安裝工具盡量使用專用工具，避免使用布類和短纖維之類的東西。

3、 Use proper and accurate installation tools for guide rail, try to use special tools, and avoid using cloth and short fiber.

四、防止導軌的銹蝕，直接用手拿取導軌時，要充分洗去手上的汗液，或者請佩戴手套，并涂以優良礦物油后再進行操作，在雨季和夏季尤其要注意防銹。

4、 To prevent the rust of the guide rail, when taking the guide rail directly with your hands, you should fully wash the sweat on your hands, or wear gloves, and apply fine mineral oil before operation, especially in the rainy season and summer.

因而在使用時要求有相當?shù)厣髦貞B(tài)度，即變是使用了高性能的導軌，如果使用不當，也不能達到預期的性能效果，而且容易使導軌損壞。不過，在某種特殊的操作條件下，導軌可以獲得較長于傳統計算的壽命，特別是在輕負荷的情況下。

Therefore, it is required to be quite cautious when using the guide rail. Even if the high performance guide rail is used improperly, the expected performance effect cannot be achieved, and the guide rail is easy to be damaged. However, under some special operating conditions, the guide rail can obtain a longer life than the traditional calculation, especially under light load.

此外，對有多處導軌需要潤滑的機械，還采用管道連接各潤滑處的集中供脂方式。脂潤滑可做到充填一次潤滑脂后長時間不需補充，而且其密封裝置的結構也較簡單，因此使用廣泛。更多相關內容就來我們網站http://www.zsdress.com咨詢！

In addition, for machinery with multiple guide rails that need to be lubricated, the centralized grease supply method of connecting pipes to each lubrication point is also adopted. Grease lubrication can be filled with grease for a long time without replenishment, and the structure of its sealing device is also relatively simple, so it is widely used. Come to our website for more relevant content http://www.zsdress.com consulting service