導軌滑塊作為機械傳動中的關鍵部件，其順暢運行離不開合理的潤滑。潤滑脂能減少滑塊與導軌之間的摩擦磨損，降低運行噪音，延長設備使用壽命。掌握正確的潤滑脂添加方法，是保證導軌滑塊性能的重要環節，需按照規范步驟操作，兼顧細節處理。

　　As a key component in mechanical transmission, the smooth operation of the guide rail slider relies on proper lubrication. Lubricating grease can reduce the friction and wear between the slider and the guide rail, lower the operating noise, and extend the service life of the equipment. Mastering the correct method of adding lubricating grease is an important step in ensuring the performance of the guide rail slider. It is necessary to follow the standardized steps and pay attention to details.

　　添加前的準備工作直接影響潤滑效果。要選擇適配的潤滑脂，不同型號的導軌滑塊對潤滑脂的粘度、耐溫性要求不同，需根據設備說明書的型號選購，避免因型號不符導致潤滑不良或部件損壞。例如，高速運行的導軌滑塊應選用低粘度、流動性好的潤滑脂，而在高溫環境下工作的部件則需耐溫性強的潤滑脂。其次，需清潔導軌和滑塊的潤滑部位，用干凈的抹布或毛刷表面的油污、灰塵和金屬碎屑，若油污較厚，可先用煤油擦拭，待完全干燥后再進行添加，防止雜質混入潤滑脂，加劇部件磨損。同時，準備好專用的加注工具，如黃油槍、注脂嘴等，確保工具清潔無雜質，避免污染潤滑脂。

　　The preparation work before adding directly affects the lubrication effect. Firstly, it is necessary to choose the appropriate lubricating grease. Different models of guide rail sliders have different requirements for the viscosity and temperature resistance of the lubricating grease. It is necessary to select the recommended model according to the equipment manual to avoid poor lubrication or component damage caused by inconsistent models. For example, lubricating grease with low viscosity and good fluidity should be selected for high-speed running guide rail sliders, while lubricating grease with strong temperature resistance is required for components working in high-temperature environments. Secondly, it is necessary to clean the lubrication parts of the guide rail and slider, using a clean cloth or brush to remove surface oil, dust, and metal debris. If the oil is thick, it can be wiped with kerosene first, and then added after it is completely dry to prevent impurities from mixing into the lubricating grease and exacerbating component wear. At the same time, prepare specialized filling tools such as a grease gun, grease nozzle, etc., to ensure that the tools are clean and free of impurities, and to avoid contaminating the lubricating grease.

　　判斷添加時機是合理潤滑的前提。導軌滑塊的潤滑周期需根據使用頻率和工作環境確定，一般情況下，每天連續運行 8 小時的設備，建議每兩周添加一次潤滑脂；運行頻率較低的設備，可每月添加一次。當發現滑塊運行時有異響、卡頓，或觀察到導軌表面潤滑脂明顯減少、干涸時，需及時補充。添加前需檢查潤滑脂的狀態，若潤滑脂出現硬化、結塊或變色，說明已變質，需先將舊脂干凈，再添加新脂，避免新舊脂混合影響潤滑效果。

　　Judging the timing of addition is a prerequisite for reasonable lubrication. The lubrication cycle of the guide rail slider needs to be determined according to the frequency of use and working environment. Generally, for equipment that runs continuously for 8 hours a day, it is recommended to add lubricating grease every two weeks; Devices with lower operating frequencies can be added once a month. When there is abnormal noise or jamming during the operation of the slider, or when the lubricating grease on the surface of the guide rail is significantly reduced or dried up, it is necessary to replenish it in a timely manner. Before adding, it is necessary to check the condition of the lubricating grease. If the grease hardens, clumps or changes color, it indicates that it has deteriorated. The old grease should be removed first, and then new grease should be added to avoid mixing old and new grease and affecting the lubrication effect.

　　具體添加過程需注重均勻與適量。對于帶有注脂嘴的導軌滑塊，將潤滑脂裝入黃油槍，對準注脂嘴緩慢擠壓，直有少量潤滑脂從滑塊兩端溢出，表明內部已充滿潤滑脂。添加時需控制力度，避免因壓力過大導致潤滑脂飛濺或部件變形。無注脂嘴的滑塊，可直接將潤滑脂涂抹在導軌的滑動面上，涂抹厚度以均勻覆蓋表面為宜（約 0.5-1 毫米），同時在滑塊的密封件內側也需涂抹少量潤滑脂，增強密封性，防止灰塵進入。對于多滑塊組合的導軌，每個滑塊都需單獨添加，確保潤滑均勻，避免因個別滑塊潤滑不足導致整體運行不暢。添加過程中，可手動推動滑塊往復移動幾次，使?jié)櫥诨瑝K內部充分分布，減少局部缺脂現象。

　　The specific addition process should pay attention to uniformity and moderation. For the guide rail slider with grease injection nozzle, insert lubricating grease into the grease gun, align with the grease injection nozzle and slowly squeeze until a small amount of lubricating grease overflows from both ends of the slider, indicating that the interior is filled with lubricating grease. When adding, the force should be controlled to avoid splashing of lubricating grease or deformation of components due to excessive pressure. For the slider without a grease nozzle, lubricating grease can be directly applied to the sliding surface of the guide rail, with a suitable thickness to evenly cover the surface (about 0.5-1 mm). At the same time, a small amount of lubricating grease should be applied to the inside of the sealing element of the slider to enhance sealing and prevent dust from entering. For guide rails with multiple slider combinations, each slider needs to be added separately to ensure uniform lubrication and avoid overall poor operation caused by insufficient lubrication of individual sliders. During the addition process, the slider can be manually pushed back and forth several times to fully distribute the lubricating grease inside the slider and reduce local grease shortage.

　　添加后的檢查與維護能保障潤滑效果的持久性。添加完成后，啟動設備空運行 1-2 分鐘，觀察滑塊運行是否順暢，有無異常噪音，若發現異常需立即停機檢查，排除潤滑脂過多或部件卡滯的問題。運行后再次清潔導軌表面溢出的多余潤滑脂，防止吸附灰塵形成油泥。定期檢查潤滑脂的消耗情況，結合設備運行狀態調整添加周期，在粉塵較多、濕度較大的環境中，需縮短潤滑周期，加強防護措施，如加裝防塵罩，減少雜質對潤滑部位的污染。長期停用的設備，在啟用前需重新添加潤滑脂，避免因潤滑脂干涸導致啟動時部件磨損。

　　The inspection and maintenance after addition can ensure the durability of the lubrication effect. After adding, start the device and run it idle for 1-2 minutes to observe if the slider runs smoothly and if there are any abnormal noises. If any abnormalities are found, stop the machine immediately for inspection to eliminate problems such as excessive lubricating grease or component jamming. After operation, clean the excess lubricating grease that overflows from the surface of the guide rail again to prevent the adsorption of dust and the formation of oil sludge. Regularly check the consumption of lubricating grease, adjust the addition cycle according to the operating status of the equipment. In environments with high dust and humidity, it is necessary to shorten the lubrication cycle and strengthen protective measures, such as installing dust covers to reduce the pollution of impurities on the lubrication parts. Equipment that has been out of use for a long time needs to be refilled with lubricating grease before use to avoid component wear during startup due to dry lubricating grease.

　　本文由導軌絲杠友情奉獻.更多有關的知識請點擊:http://www.zsdress.com真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the guide screw For more information, please click: http://www.zsdress.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.